- Here’s An Opinion On:
- Faac Automatic Gates Opener
Submitted by: Jennifer Cheek
Question: 1
A technician needs to limit the amount of broadcast traffic on a network and allow different segments to communicate with each other. Which of the following options would satisfy these requirements?
A. Add a router and enable OSPF.
B. Add a layer 3 switch and create a VLAN.
C. Add a bridge between two switches.
D. Add a firewall and implement proper ACL.
Answer: B
Explanation:
We can limit the amount of broadcast traffic on a switched network by dividing the computers into logical network segments called VLANs.
A virtual local area network (VLAN) is a logical group of computers that appear to be on the same LAN even if they are on separate IP subnets. These logical subnets are configured in the network switches. Each VLAN is a broadcast domain meaning that only computers within the same VLAN will receive broadcast traffic.
To allow different segments (VLAN) to communicate with each other, a router is required to establish a connection between the systems. We can use a network router to route between the VLANs or we can use a Layer 3 switch. Unlike layer 2 switches that can only read the contents of the data-link layer protocol header in the packets they process, layer 3 switches can read the (IP) addresses in the network layer protocol header as well.
Incorrect Answers:
A: OSPF (Open Shortest Path First) is a link-state IP routing protocol used for very large enterprise networks. It is not used to limit broadcast traffic within networks. You could use a router and divide the network into smaller subnets to limit broadcast traffic; however, you would not use OSPF as the routing protocol.
C: A bridge is a layer 2 (data-link layer) device that splits a LAN into two separate collision domains and filters the packets passing between them by using their hardware addresses. However, a bridge will forward broadcast traffic between the collision domains so broadcast traffic will not be reduced.
D: A firewall is used to restrict traffic between networks or subnets (typically between the Internet and the LAN) based on rules that specify source/destination IPs and port numbers. You would not use a firewall within a network to limit broadcast traffic on the network.
References:
Zacker, Craig, CompTIA Network+ Exam N10-005 Training Kit, OReilly Media, Inc., Sebastopol, 2012, p 134
Question: 2
The network install is failing redundancy testing at the MDF. The traffic being transported is a mixture of multicast and unicast signals. Which of the following would BEST handle the rerouting caused by the disruption of service?
A. Layer 3 switch
B. Proxy serve
C. Layer 2 switch
D. Smart hu
Answer: A
Explanation:
The question states that the traffic being transported is a mixture of multicast and unicast signals. There are three basic types of network transmissions: broadcasts, which are packets transmitted to every node on the network; unicasts, which are packets transmitted to just one node; and multicasts, which are packets transmitted to a group of nodes. Multicast is a layer 3 feature of IPv4 & IPv6. Therefore, we would need a layer 3 switch (or a router) to reroute the traffic. Unlike layer 2 switches that can only read the contents of the data-link layer protocol header in the packets they process, layer 3 switches can read the (IP) addresses in the network layer protocol header as well.
Incorrect Answers:
B: There are different types of proxy server, the most common being a web proxy server. When a client application such as a web browser requests a web page, the request is sent to the proxy server. The proxy server will then fulfill the request either by serving a cached page or by requesting the web page from the web server. This can improve performance (less web pages being downloaded over an Internet connection) and improve security (web page requests can be blocked). A proxy server is not used to reroute unicast and multicast traffic in the event of a network connectivity interruption.
C: A layer 2 switch that can only read the contents of the data-link layer (layer 2) protocol header in the packets they process. A layer 2 switch cannot route multicast (layer 3) traffic.
D: Years ago, switches were very expensive compared to hubs. Nowadays, switches are much cheaper so most people use switches rather than hubs. Computers connect to hubs in the same way they connect to switches. However, traffic sent to one hub port will be forwarded out of all the other ports because hubs do not maintain a MAC address table so they do not know which port a destination computer is connected to. A smart hub has some added intelligence that enables it to detect and isolate network problems. However, a smart hub does not reroute traffic.
References:
Zacker, Craig, CompTIA Network+ Exam N10-005 Training Kit, OReilly Media, Inc., Sebastopol, 2012, p 134
http://whatis.techtarget.com/definition/proxy-serve
http://searchnetworking.techtarget.com/answer/What-is-a-smart-hub-as-opposed-to-one-that-is-not-dumb-hu
Question: 3
Which of the following network devices use ACLs to prevent unauthorized access into company systems?
A. IDS
B. Firewall
C. Content filte
D. Load balance
Answer: B
Explanation:
A firewall is a system designed to prevent unauthorized access to or from a private network. Firewalls are frequently used to prevent unauthorized Internet users from accessing private networks connected to the Internet, especially intranets. Firewalls use ACLs (access control lists) to determine which traffic is allowed through the firewall. All traffic entering or leaving the intranet passes through the firewall, which examines each message and blocks or allows the message depending on rules specified in the ACL. The rules in the ACL specify which combinations of source IP address, destination address in IP port numbers are allowed.
Incorrect Answers:
A: An intrusion detection system (IDS) is a hardware device or software application that monitors network or system activities for malicious activities or policy violations and produces reports to a management station. An IDS does not use an ACL to prevent unauthorized access into company systems.
C: The most common type of content filter is a web content filter. A web content filter is a hardware device or software application that examines web pages as they are downloaded. The page can then be blocked if it does not comply with company web policy. A content filter does not use an ACL to prevent unauthorized access into company systems.
D: A load balancer is a hardware device or software application that directs traffic between multiple servers to balance the load between the servers. For example, if you have multiple web servers serving the same content, a load balancer will evenly distribute requests for the web pages between the servers. A load balancer does not use an ACL to prevent unauthorized access into company systems.
References:
http://www.webopedia.com/TERM/F/firewall.html
http://en.wikipedia.org/wiki/Intrusion_detection_system
Question: 4
Which of the following is used to define how much bandwidth can be used by various protocols on the network?
A. Traffic shaping
B. High availability
C. Load balancing
D. Fault tolerance
Answer: A
Explanation:
If a network connection becomes saturated to the point where there is a significant level of contention, network latency can rise substantially.
Traffic shaping is used to control the bandwidth used by network traffic. In a corporate environment, business-related traffic may be given priority over other traffic. Traffic can be prioritized based on the ports used by the application sending the traffic. Delayed traffic is stored in a buffer until the higher priority traffic has been sent.
Incorrect Answers:
B: High availability is a term used to describe a network or system that can remain operational in the event of a component failure. For example, two servers in a cluster are a common high availability solution. If one server fails, the other takes over. In networking terms, high availability would include redundant network links and network devices such as switches and routers such that computers would still be able to communicate in the event of a failure of any network device. High availability is not used to define how much bandwidth can be used by various protocols on the network.
C: A load balancer is a hardware device or software application that directs traffic between multiple servers to balance the load between the servers. For example, if you have multiple web servers serving the same content, a load balancer can evenly distribute requests for the web pages between the servers. Load balancing is the process of distributing a load between resources. Load balancing is not used to define how much bandwidth can be used by various protocols on the network.
D: Fault tolerance is similar to high availability. It describes a systems ability to remain available in the event of a component failure. Fault tolerance is not used to define how much bandwidth can be used by various protocols on the network.
References:
http://searchnetworking.techtarget.com/definition/traffic-shaping
Question: 5
Which of the following is used to authenticate remote workers who connect from offsite? (Select TWO).
A. OSPF
B. VTP trunking
C. Virtual PBX
D. RADIUS
E. 802.1x
Answer: D, E
Explanation:
D: A RADIUS (Remote Authentication Dial-in User Service) server is a server with a database of user accounts and passwords used as a central authentication database for users requiring network access. RADIUS servers are commonly used by ISPs to authenticate their customers Internet connections.
Remote users connect to one or more Remote Access Servers. The remote access servers then forward the authentication requests to the central RADIUS server.
E: 802.1X is an IEEE Standard for Port-based Network Access Control (PNAC). It provides an authentication mechanism to devices wishing to attach to a network.
802.1X authentication involves three parties: a supplicant, an authenticator, and an authentication server. The supplicant is a client that wishes to attach to the network. The authenticator is a network device, such as an Ethernet switch, wireless access point or in this case, a remote access server and the authentication server is the RADIUS server.
Incorrect Answers:
A: OSPF (Open Shortest Path First) is a link-state IP routing protocol used for very large enterprise networks. OSPF is not used for the authentication of remote users.
B: VTP trunking is used for the propagation of VLAN information between network switches. A VLAN is a logical segmentation of the network performed by a layer 2 Ethernet switch. When a switch is configured with one or more VLANs, VTP trunking can be used to propagate the VLAN configuration to the other switches. VTP trunking is not used for the authentication of remote users.
C: A PBX (Private Branch eXchange) is a hardware system used in a telephone network. A PBX performs the routing and switching of calls between a business location and the telephone network. A virtual PBX is a software based PBX. A virtual PBX is not used for the authentication of remote users.
References:
http://en.wikipedia.org/wiki/IEEE_802.1X
http://www.techopedia.com/definition/26152/vlan-trunking-protocol-vtp
About the Author: Test Information:Total Questions: 329Test Number: N10-006Vendor Name: CompTIACert Name: COMPTIA NETWORK+Test Name: CompTIA Network+ Certification ExamOfficial Site:
examcertify.co.uk
For More Details:
examcertify.co.uk/N10-006.html
Get20% Immediate Discount on Full Training MaterialDiscount Coupon Code: 3219R86597
Source:
isnare.com
Permanent Link:
isnare.com/?aid=1959760&ca=Internet}